Bio Nil
P2
Bionil P2 Pickling Paste
Weld Stain Cleaning Paste
Brush-applied pickling paste that removes weld discolouration, heat-treatment scale, corrosion and rust stains from stainless steel weld zones.
View
Bio Nil
Bionil P3 Pickling Spray
Weld and Surface Cleaning Spray (P3S for 300-series duplex)
Bio Nil· P3
Bionil P3 Pickling Spray
Weld and Surface Cleaning Spray (P3S for 300-series duplex)
Removes weld discolouration, heat-treatment stains, oxidation, pitting, light dirt and oils, and fabrication contamination from stainless steel surfaces in a single operation and prepares the surface for passivation. Bionil P3S provides an even more effective solution for 300-series duplex stainless steels. Does not damage or yellow the surface. Gives the surface a homogeneous and permanent silver colour. Suitable for AISI 304-316-321 and their derivatives.
Key Features
- Easy, visibly traceable spraying thanks to its structure
- Minimal toxic gas emissions and nitrite by-products
- A homogeneous and bright surface
Application Images
The product in application
Spray application on large surfaces — homogeneous distribution
Bionil P3 — on-site spray application
Technical Properties
Specifications
| Property | Value |
|---|---|
| Form | Spray |
| Reaction time | 45-90 minutes at 20°C (cold application) |
| Consumption | 4-6 m²/kg |
| Application | Onto the surface with a hand sprayer or compressed-air pump |
| Compatibility | AISI 304-316-321 and derivatives; P3S for 300-series duplex |
Material Compatibility
AISI 304AISI 316AISI 321300-series duplex
Usage Areas
Where is it used?
- Large-surface weld cleaning
- Sites requiring fast application
- Tank exterior surfaces
- Mixed horizontal/vertical areas
Application Procedure
Step-by-step usage
- 01
Remove heavy dirt and oils from the surface with Bionil PF
- 02
Shake the container contents until the mixture is homogeneous
- 03
Apply the mixture to the surface with a hand spray gun or a compressed-air pump
- 04
At the end of the reaction time, rinse with clean water at 100-150 bar pressure
- 05
Allow to dry naturally; do not touch by hand
Application step01 / 05
01
Remove heavy dirt and oils from the surface with Bionil PF
- 01
Remove heavy dirt and oils from the surface with Bionil PF
- 02
Shake the container contents until the mixture is homogeneous
- 03
Apply the mixture to the surface with a hand spray gun or a compressed-air pump
- 04
At the end of the reaction time, rinse with clean water at 100-150 bar pressure
- 05
Allow to dry naturally; do not touch by hand
Hazard ClassificationGHS / CLP — typical reference
Hazard Statements (H)
- H290May be corrosive to metals.
- H314Causes severe skin burns and eye damage.
- H335May cause respiratory irritation.
Precautionary Statements (P)
- P280Wear protective gloves/protective clothing/eye protection/face protection.
- P260Do not breathe mist/vapours/spray.
- P305+P351+P338IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P303+P361+P353IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
- P310Immediately call a POISON CENTER or doctor.
The classification above shows typical reference values for acid-based pickling/passivation products. Always refer to the product's current Safety Data Sheet (SDS/MSDS) for binding information; contact us for product-specific classification.
Safety Warnings
- Do not apply under direct sunlight
- Do not apply to very hot surfaces (+25°C)
- Use personal protective equipment such as goggles, gloves and an apron
- In case of skin contact, rinse with plenty of water
Related Products
